• Complete field kit for ESD floor resistance testing, built around the Megohmmeter Model 6536
• Measures both point-to-ground and point-to-point resistance
• Two 5-lb (2.3 kg) NFPA floor weights with conductive rubber bases, compliant with EOS/ESD 11.11
• Simple method: probes three feet apart, apply known voltage, record resistance
• Supports ANSI/ESD STM 7.1, STM 97.1, STM 11.11, ASTM F150, IEC 61340-4-1, MIL-STD-1686
• Meter provides variable 10 to 100V test voltage and insulation resistance to 20 GΩ
• Rugged field case holds the full kit for portable, repeatable audits
• Meter rated 600V CAT IV, IP 54; six AA batteries

• ESD-protected area (EPA) floor qualification and periodic compliance audits
• Electronics manufacturing, assembly, and cleanroom floor testing to ANSI/ESD standards
• Hazardous areas with flammable gas or liquid, where static control reduces ignition risk
• Labs and QC programs verifying static dissipative and conductive flooring performance

• Type: electrostatic discharge (ESD) floor test kit, based on Megohmmeter Model 6536
• Test modes: point-to-ground and point-to-point resistance
• Standards supported: ANSI/ESD STM 7.1, ANSI/ESD STM 97.1, ANSI/ESD STM 11.11, ASTM F150, IEC 61340-4-1, MIL-STD-1686
• Test method: two 5-lb NFPA probes placed three feet apart, known voltage applied, resistance recorded
• Floor weights: 2, 5 lb (2.3 kg) each, conductive rubber bottom pad, compliant with EOS/ESD 11.11
• Meter insulation test voltage: variable 10 to 100V in 1V steps
• Meter insulation resistance range: 10V: 2 kΩ to 2 GΩ; 100V: 20 kΩ to 20 GΩ (max 20 GΩ)
• Meter AC/DC voltage: 0.3 to 700V; continuity 200 mA / 20 mA; resistance 1Ω to 1000 kΩ
• Meter power: six AA batteries; dimensions 8.31 x 4.25 x 2.36 in (211 x 108 x 60 mm); weight 1.87 lb (850 g)
• Meter safety: IEC/EN 61010-1, 600V CAT IV, IEC 61557; IP 54
• Kit field case: rugged carrying case (IP67 field case, per accessory 2155.77; exact case model to be confirmed)

The AEMC 6536 ESD Floor Test Kit is built for one job: proving that a floor controls static the way an ESD-protected area requires. Static build-up and discharge threaten sensitive electronics and create ignition risk near flammable gas or liquid, and some components can be damaged by discharges as low as 30V. This kit measures the floor's resistance so you can confirm it stays within the limits of the applicable standard.

The kit pairs the variable-voltage Megohmmeter Model 6536 with two 5-lb (2.3 kg) NFPA floor weights that have conductive rubber bases compliant with EOS/ESD 11.11. The procedure is direct: place the two probes three feet apart on the floor, apply a known voltage, and record the resistance. The 6536 measures both point-to-ground and point-to-point resistance, supporting compliance with ANSI/ESD STM 7.1, ANSI/ESD STM 97.1, ANSI/ESD STM 11.11, ASTM F150, IEC 61340-4-1, and MIL-STD-1686.

Everything ships in a rugged field case: the meter, both weighted probes, leads, clips, test and grip probes, adapters, batteries, and manual. It is ready for repeatable floor audits in cleanrooms, electronics manufacturing, labs, and hazardous areas.